CCNA 2 (Version 7.00) SRWE Practice Final Exam Answers
Dec 21, 2019 · Switch (config-if)# switchport access vlan 1. Explain: With the router-on-a-stick method, the switch port that connects to the router must be configured as trunk mode. This can be done with the command Switch (config-if)# switchport mode trunk. The other options do not put the switch port into trunk mode. 2.
ITN (Version 7.00) Final PT Skills Assessment (PTSA) Exam Answers
Dec 20, 2019 · 1) Assign the first IPv4 address of each subnet to a router interface. LAN 1 is hosted on R1 G0/0/1. LAN 2 is hosted on R1 G0/0/0. 2) Assign the last IPv4 address of each subnet to the PC NIC. 3) Assign the second IPv4 address of LAN 1 to S1 SVI.
CCNA 1 v7.0 Curriculum: Module 10 – Basic Router Configuration
10.3.4. Packet Tracer – Connect a Router to a LAN. In this activity, you will use various show commands to display the current state of the router. You will then use the Addressing Table to configure router Ethernet interfaces. Finally, you will use commands to verify and test your configurations. 10.3.4 Packet Tracer – Connect a Router to ...
CCNA 3 v7 Modules 1 – 2: OSPF Concepts and Configuration Exam …
Dec 22, 2019 · Change the subnet mask of interface FastEthernet 0/0 to 255.255.255.0. Remove the passive interface command from interface FastEthernet 0/0. Add the network 10.0.1.0 0.0.0.255 area 0 command to the OSPF process. Modules 1 – 2: OSPF Concepts and Configuration Packet Tracer 40.09 KB 8472 downloads.
CCNA 2 v7.0 Final Exam Answers Full - Switching, Routing and …
Dec 21, 2019 · CCNA 2 v7 Switching Routing and Wireless Essentials-Version-Final-Answers-23. Packets that are received from the Internet will be forwarded to one of the LANs connected to R1 or R2. Packets with a destination network that is not 10.10.0.0/16 or is not 10.20.0.0/16 or is not a directly connected network will be forwarded to the Internet.
10.3.4 Packet Tracer – Connect a Router to a LAN (Answers)
May 14, 2023 · Step 2: Test end-to-end connectivity across the network. You should now be able to ping from any PC to any other PC on the network. In addition, you should be able to ping the active interfaces on the routers. For example, the following should tests should be successful: From the command line on PC1, ping PC4.
How to use “Static Route” on ASUS Router | SNBForums
Feb 19, 2016 · 1.Suppose you want to access another subnet which connected behind your router. Ex. Add LAN Static Route to allow Test Station1 to access Test Station2.You can add LAN static route on ASUS Router’s LAN-Route page, refer to the picture 1 about network topology. 2.Suppose you want to access another network which at your WAN side but not the ...
Seeking Wired Router with multiple 2.5Gb Ethernet Ports
Oct 29, 2021 · Alternatively you need something like this. Nighthawk CAX80 – DOCSIS 3.1 Cable Modem Router with WiFi 6 | NETGEAR. The Nighthawk AX8 WiFi 6 Cable Modem Router pairs DOCSIS 3.1 with WiFi 6 to give you the performance that today's smart homes demand. Buy now! www.netgear.com.
Wireguard VPN Client: killswitch activation -> LAN administration …
Sep 9, 2024 · LAN devices cannot access router admin interfaces [http (s), ssh, ping] via router LAN IP. Possible explanation: - Unclear, but killswitch seems to block access to any resource beyond router LAN IP. Fixes tried: - Add explicit VPN Director rules binding traffic between a device LAN IP and router LAN IP to the WAN Iface.
CCNA 2 v7 Modules 1 - 4: Switching Concepts, VLANs, and …
Dec 21, 2019 · Explanation: A router defines a broadcast boundary, so every link between two routers is a broadcast domain. In the exhibit, 4 links between routers make 4 broadcast domains. Also, each LAN that is connected to a router is a broadcast domain. The 4 LANs in the exhibit result in 4 more broadcast domains, so there are 8 broadcast domains in all.